10 HP Dust Collector

10 HP Dust Collector

The cartridge dust collector is an excellent choice to replace the common bag-house or dust bag type collector and can be used to collect almost any dry, fine dust particulate.

2 Horsepower
4900 CFM
9 Cartridge
Reserve Pulse
Variable Frequency

Designed with 9 cartridges that reverse pulse clean via a programmable timer board and solenoid valve system. The cartridge dust collector is an excellent choice to replace the common bag-house or dust bag type collector and can be used to collect almost any dry, fine dust particulate. The cartridge offers a large amount of cleaning filter material in a very compact area. Cartridge dust collectors take up much less space than bag house collectors and offer an impressive filtration efficiency of 99.7% against 1/2 micron particles allowing for in house venting in applications that do not produce noxious or poisonous gases.

This unit is designed with a 16 inch diameter, abrasive resistant, inlet to extend the filter life. The filters are cleaned with an automatically actuated reverse pulse of compressed air. The unit pictured is the actual unit offered for sale. Picture 7 is added for display purposes but is representative, with model and color possible exceptions. This unit is currently equipped with our automated pulsing package. It is effective when used while the dust collector is in operation or shut down and can be used as desired to clean filters from accumulated particulate continuously or as required. The timer board is powered by standard 120v single phase electrical connection. It is factory programmed for 3 minute intervals, completely cycling all filters once every 9 minutes when energized.

This unit is designed to deliver optimal performance when dust cake levels of 90-180-270 pounds or less are accumulated in between pulse cleaning intervals or it may remain energized for continuous filter cleaning. It is equipped with an acoustical dampening package that will meet the maximum noise levels allowed per OSHA regulations.

The vertical placement of filters allow for the best possible release and removal of dust from the pleated filters during pulse cleaning. Three filters are cleaned at a time on this unit. It has nine, 99.7 % efficient cartridges that contain 2,034 square feet of total cleaning surface area. Each 26 inch long and 12.75 inch diameter filter cartridge has pleats that are 2.375 inches deep. The center opening of the filter is 8 inches in diameter and is open on both ends before installation. Filters in this unit are a single stack set of nine. They are one of the most popular filters made and can be replaced with any similar filter cartridge without regard to warranty restriction or voidance. Filters will require replacement generally once every 2-3 years on average. Some applications with high humidity, oily, fibrous, magnetic, or aglomeric particulates may reduce this substantially.

Currently, it is offered with a 10 hp, (208v - 230v / 460v) 3 phase TEFC motor as standard equipment ( 25 - 24 / 12 amps ). The approx. dimension of this collector is 11 ft. high, 5 ft. wide and 6 ft. deep. It is pictured with a barrel kit for 55 gallon drum disposal.

Our Dust Collectors are Equipped with our VFD electrical package

Soft Motor Starting - The amperage draw will not exceed the motor name plate rated amperes at any time.
Easy On - Off Switch - Conveniently located on the dust collector, this is a simple 24 volt relay loop that engages the variable frequency drive with the push of a button.
Thermal Motor Protection - The motor drive will constantly monitor the motor and the drive itself for any unusual spike in temperature throughout. If the temperature rises above acceptable parameters the drive will default and shutdown before any damage to the unit is sustained.
Motor Fault and Report Monitoring - The motor drive is capable of displaying motor torque, hours of operation, actual amperage draw, percentage of motor capacity used, percentage of drive capacity used, the motor frequency in hertz, delivered line voltage and several other programmable LED display readouts. Factory settings are always in hertz frequency unless specified otherwise.
Automatic Load Compensation Controls - The motor drive is programmed to compensate for changing load conditions. These conditions include but are not limited to extended length or reduced diameter of piping, blast gates and other restrictions in the air lines, atmospheric humidity, temperature and altitude adjustments, filter cartridge dust cake levels, and power supply brownout or overcurrent conditions.